Disclaimer***Acura TSX V6-3.5L Technical Service Bulletin # 09-016 Date 120522
Body - Windshield Side Trim Retainer Is Loose
09-016
May 22, 2012
Applies To
2010-12 TSX - ALL
Windshield Side Trim Retainer Is Loose
(Supersedes 09-016, dated January 12, 2012, to revise the information marked by the black bars and asterisks)
REVISION SUMMARY
^ In Applies To, 2009 models were removed, and 2012 models were added.
^ Under PARTS INFORMATION, more windshield side trim part numbers were added.
CORRECTIVE ACTION
Remove both windshield side trim pieces, and replace any retainers that are loose or missing. Then, reinstall the trim pieces.
25
PARTS INFORMATION
TOOL INFORMATION
KTC Trim Tool Set TN SQJATP2014
REQUIRED MATERIALS
Konishi Bond SL211B PN 08713-0008
(one tube repairs about two vehicles)
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Failed Part PN 91573-TL0-E01
Defect Code 06201
Symptom Code 06101
Skill Level Repair Technician
NOTE
Do not submit the Konishi Bond as a replacement part. Please submit under materials. Since one tube of Konishi Bond repairs two vehicles,
the cost of the material should equal 12 of the dealer net cost.
REPAIR PROCEDURE
NOTE
^ The bridges on the windshield side trim may break when removing the trim.
^ Make sure not to break the bottom clip retainer tabs so the trim can be reused.
^ Allow the adhesive to cure for a minimum of 24 hours before removing the tape from the vehicle.
^ Advise the client not to wash the vehicle for at least 24 hours.
^ To watch a video demonstration of this procedure in Tech2Tech.
26
1. Starting at the top, work your way down to remove the windshield side trim from the retainers using the appropriate KTC trim tool.
NOTE
Make sure you do not damage the rubber seal on the windshield side trim.
2. Slide the trim up to release it from the bottom clip.
3. Inspect the bottom clip retainer tabs on the windshield side trim.
^If the bottom clip retainer tabs are broken or stress whitened, discard the trim and use a new windshield side trim to complete the repair, then go
to step 9.
If the bottom clip retainer tabs are OK, go to step 4.
27
NOTE
The new windshield side trim comes with new retainers and a bottom plastic clip.
4. Inspect the trim for retainers. If any retainers are attached, bend the tabs out to remove them from the trim.
5. Inspect the windshield side trim for broken or cracked bridges. If a bridge is broken or cracked, use diagonal cutters and trim it as shown.
28
6. Remove the plastic bottom clip on the vehicle by turning it 90 degrees. If the bottom clip is damaged or stress-whitened, replace it.
7. Reinstall the plastic bottom clip onto the windshield side trim. Make sure the projection on the clip
8. Clean the trim with a shop towel dampened with 3M general purpose cleaner or isopropyl alcohol. Keep oil, grease, and water from getting on
the bonding surface.
9. Inspect the retainers on the vehicle
If any retainers are missing or loose, go to step 11.
If any retainers are firmly attached to the A-pillar, remove any plastic trim pieces from them with a flat-tip screwdriver. Go to step 10.
29
10. Bend the tabs on the retainers back into place as shown.
11. Remove any loose retainers or adhesive from the body
^ Using a heat gun, heat the retainer or adhesive to 212锟斤拷-248锟斤拷F (100-120锟斤拷C). Avoid damaging the paint by applying heat gradually.
^ Use a plastic scraper to remove the loose retainer or glue from the body.
^ Be careful not to scratch the body.
^ While applying heat, use the plastic scraper to remove any double-sided tape that may be stuck to the A-pillar.
12. Clean the bonding surface on the body with a shop towel dampened with 3M General Purpose Adhesive Cleaner or isopropyl alcohol. After
cleaning, keep oil, grease, and water from getting on the bonding surface.
13. Cut the Konishi Bond applicator tip to a diameter of 6 mm.
30
14. Apply a thin layer of Konishi Bond to the entire bonding surface on each new retainer as shown.
15. Install the new retainers in the locations where the
original retainers were removed, and allow the Konishi Bond to cure for 15 minutes before going to the next step.
16. As a guide, lay the windshield side trim down next to the retainers before applying the Konishi Bond.
31
17. Starting at the bottom, apply a bead of Konishi Bond between each retainer, and into any retainer where the windshield side trim bridge location
was cut out. Make sure the bead is at least 5 mm high.
NOTE
Konisihi Bond adhesive begins curing with exposure to moisture in the atmosphere. Do step 18 immediately after applying the adhesive. Do
not apply Konishi Bond into any retainer where the bridge is still intact on the windshield side trim.
18. Starting at the top, position the windshield side trim to align the top retainer between the trim alignment ribs. Firmly press the trim into the
retainers and bottom clip hole until they click into place.
32
NOTE
^ The trim will click into place only where the bridge on the trim is intact.
^ If you don't confirm that the windshield side trim has clicked into place, you may get a comeback.
19. Secure the trim with low-tack masking tape as shown.
20. Repeat steps 1 thru 19 on the other side.
NOTE
^ Allow the adhesive to cure a minimum of 24 hours before removing the tape from the vehicle.
33
^ Advise the client not to wash the vehicle for at least 24 hours.
^ To prevent the remaining Konishi Bond adhesive from curing in the tube, squeeze the tube from the bottom to remove any air before
