Disclaimer***Acura TL AWD V6-3.7L Technical Service Bulletin # 08-041 Date: 120823
Navigation System - Overview/Set Up/Controls
08-041
August 23, 2012
*Applies To:
2009-13 TL With Navigation - ALL*
2009-12 TL: TQI of the Navigation System
(Supersedes 08-041, dated March 4, 2011, to revise the information marked by the black bars and asterisks)
*REVISION SUMMARY
^ In Applies To, 2013 models were added.
^ Under INTRODUCTION, new information was added.*
INTRODUCTION
This bulletin provides information for the TQI, including testing, of the navigation system. These topics are covered:
^ Navigation System Controls
^ Navigation System Setup at the TQI
^ Rearview Camera
^ Resetting the AcuraLink Control Unit to Clear DTCs
^ System Limitations
^ Map Coverage Areas
^ Hawaii, Alaska, and Puerto Rico System Setup
^ AcuraLink(TM) Real-Time Traffic Information
^ XM Weather Information
5
^ Ordering Navigation Update Software
For more information about the navigation system and its operation, refer to these resources:
^ Quick Start Guide or Advanced Technology Guide
^ Online University - Use the keyword NAVI for more information about the navigation system.
^ Navigation Manual - Besides the one that comes with the vehicle, the navigation manual is also available online. Select Search by vehicle,
vehicle, then enter keywords NAVIGATION MANUAL.
*^ Online University - Go to the SALES tab, select Course Catalog under Quick Links, and use the keyword NAVI for more information about the
navigation system.*
WARRANTY CLAIM INFORMATION
None. These procedures are considered part of the normal TQI.
NAVIGATION SYSTEM CONTROLS
The buttons listed above are used in this service bulletin. For more information on the button functions, see Getting Started in the navigation manual.
Voice Control System
6
The navigation system features a voice control system that allows you to operate most of the navigation, HVAC, and audio controls with only your
voice. To interact with the navigation system, use the TALK and BACK buttons. The microphone is located on the ceiling. This is the primary way
to give commands to the system.
TALK button - Press and release this button on the steering wheel to activate the voice control system. After pressing and releasing the TALK
button, wait for the beep, and then speak the command.
BACK button - Press this button to return to the previous screen. After the previous screen appears, the system prompts you for a command, and
beeps. Press and release the TALK button to say your next command. The BACK button has the same function as the CANCEL button located next
to the interface dial.
Microphone - Receives voice commands.
Improving Recognition
If the system does not understand your voice commands, refer to Improving Voice Recognition in the navigation manual.
NOTE:
^ You must be in the driver's seat to use voice commands with the navigation system.
^ If you speak a command with something in your mouth, with a heavy accent, or in a high-pitched voice, the system may misinterpret your
voice command.
NAVIGATION SYSTEM SETUP AT THE TQI
The navigation system is basically ready to use when the vehicle is delivered to the dealership. Since the system interfaces with other vehicle
systems, it is important that all of the systems are initialized. To initialize the navigation system, follow these steps:
1. Do the normal TQI of the vehicle, including the audio system. The navigation system will not function until its 5-digit anti-theft code has been
entered.
7
2. You may see the factory In-Line Diagnosis screen below. If so, do the following or this screen will return every time the vehicle is started. If not,
go to step 3.
^ Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time until the Select Diagnosis Items screen comes up. Then
release the buttons.
^ Press and hold the MAP/GUIDE button until the Inline Diag CSF Setting screen appears.
^ Set the Inline Diag Setting to Complete, and make sure the CSF Setting is ON, then select Return twice to exit the diagnostic mode.
3. Start the engine, and drive the vehicle outside, away from buildings, tall trees, and power lines. Then enter the 5-digit anti-theft code for the
audio and navigation system. The code is on the Navigation Anti-Theft Code card.
NOTE:
There are two code labels and a plastic code card located in a small plastic bag in the glove box.
^ Attach one of the labels to the code card, put it in the plastic bag, and return it to the glove box.
^ Attach the other label to the TQI repair order, or put it in the plastic bag, and return it to the glove box for the client.
NOTE:
Never attach a label to the side of the glove box or other location where both the serial number and code are easily visible. This defeats the
purpose of the anti-theft protection.
If the code card is lost or unavailable, you can get the code from the iN (Interactive Network) using the navigation system serial number. The
system serial number can easily be obtained without removing the navigation unit. To get the serial number and the code, do this:
^ Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time.
^ At the Select Diagnosis Items screen, select Detail Information & Settings, select Unit Check, then Navi ECU. The system runs a brief
diagnostic, then the navigation unit serial number is displayed at the bottom of the screen.
^ Use the navigation Anti-theft code inquiry option on the iN to look up the 4-digit navigation anti-theft code.
^ If the code does not work, call the Acura warranty department.
8
4. The instructions below appear on the screen to indicate that the system is initializing (determining its location from the GPS satellites). Follow
the on-screen instructions.
NOTE:
The average initialization takes about 10 minutes, but it can take as long as 45 minutes. If initialization completes within 10 minutes, the
display changes to the globe screen.
5. If the system does not initialize within 10 minutes, a second screen (shown below) appears. The system is still initializing but will not
automatically exit to the globe screen when the initialization is complete. Do not immediately follow the instructions on the screen. After 30
minutes, try restarting the engine to see if the navigation system completed the initialization. If it did not, follow the instructions on the screen.
NOTE:
The initialization screen may appear after battery voltage to the navigation control unit has been disconnected for more than 5 minutes. If this
happens, follow the on-screen instructions. If you are still unable to obtain GPS initialization, refer to the service manual for diagnostic
information.
6. When initialization is complete, the disclaimer screen appears. Select OK.
NOTE:
Do not enter a destination yet. For the navigation system to calculate a route, it must align the current location to a mapped road (map
matching). This happens when you start driving.
7. Make sure the XM Radio dealer demo account is active by tuning to several channels within the full XM lineup. To see the full list of XM
channels, go to www.xmradio.com.
NOTE:
For 2009-12 models with navigation, XM Radio, XM weather, and real-time traffic are free to the clients for the first 3 months. After that,
clients must subscribe to XM Radio, XM weather, and/or real-time traffic to continue receiving coverage by calling 800-852-9696, or going
online to www.xmradio.com. They will need their XM radio ID (displayed when you tune to channel 0) and a major credit card.
8. Drive the vehicle at least a half-mile from your dealership, and find a safe place to park. Then set the map scale to 1/20.
^ Make sure the VP (vehicle position) icon moves smoothly as you drive and does not jerk from one point to another. Also make sure the icon
points in the direction the vehicle is traveling; it does not "dog track" or spin.
9
^ Af6er driving a few hundred feet, the name of the road you are driving on should appear at the bottom of the screen.
NOTE:
If the navigation system fails to map-match after the vehicle is driven more than a couple of miles on a displayed road, refer to the service
manual symptom troubleshooting.
9. With the map screen displayed, press and release the TALK button.
10. When you hear the beep, say "find the nearest Acura dealer." The system should display a list of Acura dealers.
11. Rotate the interface dial to highlight your dealership, then push in on the ENTER button.
12. On the Calculate Route to screen, select OK. The system then calculates a route and displays it as a blue line. If you are in a rural area with
unverified roads, you may see a blue vector line or a blue/pink dotted line pointing in the direction of your destination.
13. Follow the voice guidance back to your dealership. The voice guidance should work even with the audio system turned off.
14. With the map screen displayed, check the system interaction with the audio system and the lower display. Press and release the TALK button.
After the beep, say "XM channel 122." The lower display should change to XM channel 122 and show CNN News.
15. With the map screen displayed, check the system interaction with the climate control system. Turn on the climate control system by selecting
AUTO. Then press and release the TALK button. After the beep, say "temperature 68 degrees." The lower display should change to 68 degrees.
16. Make sure the time shown in the upper display is correct; the system gets it from the GPS satellites. For areas that do not follow daylight saving
time, you may have to adjust the time settings. Go to clock adjustment in the Setup screen, and set Auto Daylight to OFF.
NOTE:
If your dealership is located near a time zone boundary, set Auto Time Zone by GPS to OFF. The clock then keeps the "home" time if the
client routinely drives across the time zone boundary.
17. Press the DISPLAY MODE button to verify that the display changes between the Day, Night, and OFF modes.
18. If your dealership is located in a metropolitan area that has traffic incident or traffic flow data available
(see ACURALINK REAL-TIME TRAFFIC(TM) INFORMATION), do this:
^ Select one of the traffic map 1/2-, 1-, 2-, or 5-mile scales by rotating the dial.
^ Use the interface dial to scroll to the downtown area of your city. If your metro area has traffic flow data, freeways and other main roads
should show traffic flow data as red, yellow, or green lines for traffic flow in one or both directions on the road.
^ Small diamond-shaped "traffic incident" icons may be shown. If so, scroll over an icon and press in the interface dial to see the details.
^ Partially displayed traffic data does not indicate a problem with the navigation system. Traffic flow and density varies from day to day and
from one road to another. If your area has traffic, but it is not displaying on the screen, refer to the Navigation section of the appropriate
service manual.
19. Clear the Hard Disc Drive (HDD):
^ Press the engine start/stop button to select the ACC mode.
^ Turn the audio-navigation unit ON.
^ Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time until the Select diagnosis items screen comes up. Then
release the buttons.
^ Select Detail Information and Setting.
^ Select Function setup.
^ Select Clear All. A confirmation screen appears, select Yes.
^ A second confirmation screen appears. Select Yes again.
REARVIEW CAMERA
With the ignition switch in the ON (II) position, shift to R. The rearview image appears on the navigation display. Make sure the distance guidelines
appear on the screen. To turn the guidelines ON or OFF, press and hold the CANCEL button for three seconds. Turn the interface dial knob to adjust
the image brightness. This brightness adjustment is not affected by the screen brightness adjustment in Setup.
10
NOTE:
^ When you are in R, only the interface dial knob works. The other buttons are locked out.
^ If the image is foggy or dirty, clean the rearview camera lens.
^ The camera brightness cannot be adjusted by voice control.
RESETTING THE ACURALINK CONTROL UNIT TO CLEAR DTCS
AcuraLink is a two-way communication system between the vehicle and American Honda, using the XM satellites. It works with the vehicle's
navigation system, the HandsFreeLink system, and the audio system.
When the No.15 fuse is removed during vehicle shipment, the AcuraLink control unit sets DTCs. These DTCs need to be cleared during the TQI
using this procedure:
1. Start the engine.
2. On the navigation system disclaimer screen, select OK by pressing the interface dial. (The interface dial is used to control several functions,
including AcuraLink.)
3. Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time, until the Select Diagnosis Items screen is displayed.
4. Turn the interface dial to highlight the Self-Diagnosis Mode icon on the screen, then press the interface dial to select the icon. Allow the
diagnostic to run.
5. Turn the interface dial to highlight the XM (HIP) icon on the screen, then press the interface dial to select the icon.
6. Turn the interface dial to highlight the XM (HIP) Diag icon, then press the interface dial to select the icon.
NOTE:
If the select diagnosis item menu screen does not appear, do this:
^ To establish communication with the navigation system, disconnect the negative cable from the battery for 30 seconds, reconnect it, then
repeat steps 1 thru 6.
^ Because you have disconnected the battery, do this:
- Reenter the audio unit anti-theft code and enter radio station presets.
- Reenter the navigation system code.
- Redo the idle learn procedure.
7. Turn the interface dial to highlight the Data Reset icon. Then press the interface dial to select the icon.
8. Turn the interface dial to highlight the Yes icon. Then press the interface dial to select the icon.
9. Select OK by pressing the interface dial, then toggle the interface dial to the left one time.
10. Press the CANCEL button.
11. Turn the interface dial to highlight the Return icon. Then press the interface dial to select the icon.
12. Again, turn the interface dial to highlight the Return icon. Then press the interface dial to select the icon. This returns you to the navigation
system screen.
SYSTEM LIMITATIONS
These issues could arise during the TQI or after installing replacement parts to repair the system. Refer to the navigation manual or the advanced
technology guide for basic operation.
If you think you found any problems with the navigation system during the TQI or after installing replacement parts to repair the system, refer to
System Limitations and Database Limitations in the navigation manual. This helps you to avoid replacing parts when the issue may be a system
characteristic.
To minimize distractions while driving, always use the voice control system to operate the navigation system. Always verify the audio and visual
route information by carefully observing roadway signs, signals, etc. Use your own good judgment, and obey traffic laws while driving.
11
The navigation system has these limitations:
^ The GPS (Global Positioning System) satellites used by the navigation system are operated by the U.S. Department of Defense. For security
reasons, certain inaccuracies are built into the GPS. This can cause occasional positioning errors of up to several hundred feet. If the navigation
system indicates your position incorrectly, wait several seconds until it corrects itself. The system may also correct itself after you make a turn or
cross a road.
^ The routes calculated by the system may not always be what you consider the most direct ones. Try different routing methods to obtain the best
route. Even the direction your vehicle is pointing influences the route calculation.
^ Since businesses close or relocate, some information may be inaccurate. Also, route guidance may conflict with actual road conditions, such as
street closures, construction, and detours.
^ The GPS antenna receives location information from orbiting satellites. Anything that blocks or interferes with the signal affects accuracy. The
GPS signal can be blocked or interfered with (vehicle position shown incorrectly on the map) by:
- Aftermarket metallic window tinting above or to the sides of the GPS antenna.
- Aftermarket vehicle tracking systems mounted near the navigation unit or the display.
- Radar detectors, cell phones, or other aftermarket electronic accessories placed near the navigation unit or the display.
- Outside electrical interference from overhead power lines, trolley lines, or broadcast sources.
- Tall trees or buildings near or over the vehicle. They can cause the system to show the vehicle on an adjacent street. This should
automatically correct itself when the obstruction is gone.
^ In some cases, a city name, road name, or address may be incorrect or missing from the system. These are the possible causes:
- The city name may be listed under a larger metropolitan area or as an unincorporated area. Try selecting the street name first. If it is a smaller
city in a rural area, only the main road may be shown.
- If the street name cannot be found, is shown incorrectly on the map, or is not drawn correctly, it may be because it is a new road or it is in an
unverified area.
NOTE:
See the navigation manual for more information.
^ If the location of your dealership is shown incorrectly or needs to be changed, report it to your DPSM.
MAP COVERAGE AREAS
The map database covers the United States, Puerto Rico, and Canada. The map coverage for the U.S. contains accurately mapped (verified)
metropolitan areas and less accurate (unverified) rural coverage. In Canada, the database covers major metropolitan areas and major roads
connecting those metropolitan areas. Coverage extends to about 100 miles from the U.S. border. For more coverage information, go to the website.
Detailed Coverage and Non-Detailed Coverage
Many cities and metropolitan areas are fully mapped with detailed coverage while rural areas typically have less accurate, incomplete, or
non-verified information. Refer to the Introduction and Getting Started in the navigation manual for more information.
For a list of current detailed coverage areas by country and state/province, refer to the navigation manual or go online to website. Online, use the
pull-down menu to select the Model and the Year, select Map Coverage, then select Map Coverage Details.
HAWAII, ALASKA, AND PUERTO RICO SYSTEM SETUP
The HDD in the vehicle contains maps for the U.S., Puerto Rico, and Canada. If the vehicle is sold in Hawaii, Alaska, or Puerto Rico, or relocated to
one of these areas from the mainland, change the map coverage so the applicable maps are displayed. To change the map coverage for use in Hawaii,
Alaska, or Puerto Rico, do this:
1. Press and hold the MENU, MAP/GUIDE, and CANCEL buttons at the same time. The display changes to the Select Diagnosis Items screen.
2. Select Detail Information and Settings.
3. Select Coverage area.
4. Select Hawaii/Puerto Rico/AK coverage. The system may reboot.
5. Start the vehicle, and drive it to an open area so the system can acquire a GPS signal.
12
6. After the system has initialized, do the map matching by driving the vehicle on a road until the road name appears at the bottom of the map
screen.
NOTE:
^ If a vehicle is relocated from Hawaii, Alaska, or Puerto Rico to the mainland, you must change the Coverage area to US.
^ When you change the coverage area, any previous destinations, address book, and other system settings are changed to the factory defaults.
^ XM Radio is not available in Hawaii or Alaska, so there is no AcuraLink or Real-Time Traffic(TM) coverage.
ACURALINK REAL-TIME TRAFFIC INFORMATION
Traffic information is available in many metropolitan areas. The amount and type of coverage varies. Traffic incidents (diamond-shaped icons) are
shown on the screen for most major metropolitan cities (typically during daytime commutes). Many of these cities also display traffic flow, shown as
red, orange, or green bands, alongside major roads or freeways.
NOTE:
^ Traffic information will not be displayed if the XM Radio dealer demo account is not active.
^ Refer to the navigation section of the appropriate service manual to troubleshoot real-time traffic problems.
The amount of traffic coverage varies from city to city and time of day. The Acura website contains a link that provides an up-to-date list of the
current cities with traffic coverage and the actual roads covered within each city. The link also provides a demonstration of the system that explains
traffic flow color bands and incident icons displayed on the map. The link can be found at the website.
XM WEATHER INFORMATION
XM Radio now offers XM weather and radar that shows current local weather as weather icons on the map screen. These are different from weather
related traffic incident icons. The weather icons are:
13
You can also see weather warnings. Say or select Warning Map. The display changes to show weather warnings for the selected area.
ORDERING NAVIGATION UPDATE SOFTWARE
Navigation map updates can be ordered online at the website. Under Find Updates, use the pull-down menu to select the vehicle Model and Year.
You can also call the Acura Navigation Map Update Center. Both methods require a major credit card.
