Disclaimer***Acura TL AWD V6-3.7L Technical Service Bulletin # 13-007 Date: 130220
Audio, Interior - Rattle/Vibration From Rear Speakers
13-007
February 20, 2013
Applies To:
2009-12 TL - ALL
Rattle or Vibration From the Rear Speakers
SYMPTOM
254
There is a rattle or vibration coming from the rear
speakers or subwoofer when the audio system is on.
POSSIBLE CAUSE
Vibration from the subwoofer causes cracks in the rear parcel shelf at the subwoofer mounting location.
CORRECTIVE ACTION
Cut out the damaged section of the rear parcel shelf and install a service plate.
PARTS INFORMATION
Rear Parcel Shelf Kit: P/N 66500-TK4-3050
Kit includes:
^ Service Plate
^ Subwoofer Trim Ring
^ Twist Tube
^ Harness Clip
^ Bolts
C-Piller Trim Clip: P/N 91561-TA0-All (Two Required)
REQUIRED MATERIALS
Loctite Threadlocker Blue 242
J-B Weld
TOOL INFORMATION
Center Punch (commercially available)
Deburring Tool (commercially available)
Reciprocating Saw (commercially available) Reciprocating Saw Blade
(4 inches in length, 4 mm wide, 24 TPI)
(commercially available)
Rotabroach Tool Kit T/N BLR1 120S0
WARRANTY CLAIM INFORMATION
The normal warranty applies.
Operation Number: 8390A3
Flat Rate Time: 1.2 hours
Failed Part: P/N 66500-TK4-A00ZZ
Defect Code: 01801
Symptom Code: 04501
Skill Level: Repair Technician
INSPECTION PROCEDURE
255
1. Open the trunk lid. Detach the clips and remove the cargo hook buttons, then remove the side trim panel from both sides.
2. Lower the trunk upper trim panel to detach the clips, then remove the panel from the trunk compartment.
3. Visually inspect the rear shelf subwoofer attachment area for cracks.
^ If the rear shelf subwoofer attachment nut area has cracks, go to REPAIR PROCEDURE.
^ If the rear shelf subwoofer attachment area does not have any cracks, this bulletin does not apply; continue with normal troubleshooting.
REPAIR PROCEDURE
256
1. While pushing down on the rear seat cushion, pull the seat hook handles to release the hooks.
2. Remove the seat cushion, and release the center seat belt buckles from the slits.
3. Release the seat belts from their guides.
4. Remove the bolts from the base of the seat-back.
257
5. Remove the rear seat-back.
^ Lift up the bottom of the seat-back
^ Push on the seat-back while lifting it up to release the wire loops from the hooks on the body.
6. Remove the door opening seal as needed.
7. Hit the upper clip in the C-pillar trim with a rubber mallet. Hitting the clip breaks the projections on the pin and pushes it into the grommet on
the body.
NOTE:
The upper clip must be replaced with a new one when the C-pillar trim is reinstalled.
258
8. Pull back the top of the C-pillar by hand to remove the upper clip from the body.
9. Pull the C-pillar trim by hand to detach the clips to release the hooks, then pull out the trim from the rear shelf.
259
10. Remove the rear shelf.
^ Pull up the entire rear shelf to detach the clips.
^ Pull both rear seat belts and the rear center seat belt out through the slits in the rear shelf.
11. Remove the four mounting bolts from the subwoofer.
12. Disconnect the 2P connector, and remove the subwoofer.
13. Lay a drop cloth down inside the trunk area, and lay shop towels over the top side of the rear parcel shelf next to the rear speakers and seat belt
retractors to protect them from metal debris.
14. Cut out the paper template provided in the kit. Punch four holes in the template where the subwoofer mounting bolts go through.
260
15. Lay the paper template down on the top of the rear parcel shelf and install two bolts in a cross-diagonal location as shown.
NOTE:
Use the bolt locations where minimal cracking has occurred.
16. Using a felt tip pen, mark an outline of the area to be cut out on the rear parcel shelf.
NOTE:
Do not mark a larger section than the size of the template.
17. Inspect the rear shelf for cracking that may extend past the cut line. If any crack extends beyond the cut line, drill an 1/8" hole into the end of
the crack. Fill the hole and crack with J-B Weld.
261
NOTE:
Deburr the hole, then fill the hole and crack with J-B Weld.
18. From inside the trunk, attach the service plate to the underside of the rear shelf using two bolts in a cross-diagonal location.
262
19. Using a felt tip pen, mark the eight holes in the service plate to the rear shelf to be drilled.
20. Remove the service plate.
21. Use a center punch on each marked hole to prepare the surface for drilling.
22. Using an 8 mm diameter Rotabroach, drill the eight holes marked into the underside of the rear shelf.
NOTE:
Make sure to remove the metal debris from the top side of the rear parcel shelf before going to the next step.
263
23. Using a reciprocating saw with a 4 mm wide blade with 24 TPI, cut along the inside of the cut line made in step 16 to remove the damaged area
of the rear parcel shelf.
NOTE:
Chamfer and round each of the corners.
24. Using a deburring tool or metal file, debur and smooth the newly cut area.
NOTE:
Use gloves to protect your hands.
25. Use touch-up paint to coat the newly cut area, drilled holes, and any area where J-B Weld may have been used to prevent rust from occurring.
26. From inside the trunk, install the service plate to the bottom side of the rear shelf. Install the bolts from the top side of the rear shelf and into the
service plate. Bolts should be hand tight.
> Service plate
> Bolts
264
NOTE:
Apply blue loctite to the threads of the eight bolts.
27. Torque the eight service plate bolts to 6.9 to 11.9 N.m (5 to 8.8 lb.ft).
28. Carefully remove the shop towels off the rear speakers and seat belt retractor. Make sure not to drop any metal debris that may be on the towels.
29. Remove the drop cloth from inside the trunk.
30. Separate the plastic trim ring from the subwoofer and install a new one from the kit.
> Subwoofer trim ring.
265
31. If equipped, remove the compass harness and clip from its current location. Apply the twist tube from the kit around the compass harness to
protect it from bolt damage.
> Twist tube
32. Wrap the ends of the twist tube with electrical tape. Then apply a new harness clip from the kit to the location shown.
> Harness clip
33. Install the subwoofer assembly to the new service plate and torque the bolts to 2.9 to 3.9 N.m (2.2 to 3 lb-ft)
34. Connect the 2P connector to the subwoofer.
35. Vacuum the rear shelf and trunk area to remove any metal shavings.
36. Reinstall the rear shelf.
37. Reinstall the C-pillar trim with the new trim clip.
> C-Pillar trim clip
38. Reinstall the door opening seal.
39. Reinstall the rear seat back and the rear seat cushion.
40. Reinstall the trunk upper and side trim panels.
