Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 10-015 Date: 100608

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 10-015 Date: 100608

Interior - Rear Head Restraint Button Sticks/Falls Out

10-015

June 8, 2010

Applies To:

2009 TL - ALL

2010 TL 2WD - From VIN 19UUA8...AA000001 thru 19UUA8...AAO11262

2010 TL AWD - From VIN 19UUA9...AA000001 thru 19UUA9...AA004827

2010 ZDX - From VIN 2HNYB1...AH000001 thru 2HNYB1...AH501820

Rear Head Restraint Tilt Button Sticks or Falls Out

(Supersedes 10-015, dated May 18, 2010, to revise the information marked by asterisks)

*REVISION SUMMARY

Under WARRANTY CLAIM INFORMATION, the failed part number was changed.*

SYMPTOM

The rear head restraint tilt button sticks inside its housing or has fallen out.

PROBABLE CAUSE

A sustained high temperature in the interior can cause the button's locking tabs to weaken and pop loose from the button housing.

126

CORRECTIVE ACTION

Replace one or both rear restraint tilt buttons.

PARTS INFORMATION

Rear Head Restraint Tilt Button:

P/N 821 48-TK4-A11ZA (Gray, TL only)

P/N 82148-TK4-A11ZB (Black, TL and ZDX)

P/N 82148-TK4-A11ZC (Ivory, TL only)

TOOL INFORMATION

KTC Trim Tool Set: T/N S0JATP2O14

WARRANTY CLAIM INFORMATION

The normal warranty applies.

*Failed Part: P/N 82148-TK4-A11ZA*

Defect Code: 03217

Symptom Code: 05701

Skill Level: Repair Technician

REPAIR PROCEDURE

1. Move the head restraint to its upright position.

2. Position the KTC trim tool behind the tilt button as shown, and pull out on it to release the button from the head restraint.

127

3. Locate the slots in the head restraint tilt button hole, then align the slots with the tabs on the new tilt button housing.

4. With the slots and tabs aligned, push the new head restraint button in until you hear a click.

5. Pull out on the tilt button housing to make sure the button is installed securely.

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 12-043 Date: 121208

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 12-043 Date: 121208

Tire Monitor System - ATEQ VT55 TPMS Update Information

12-043

December 8,2012

Applies To:

ALL Vehicles with TPMS

ATEQ VT55 TPMS Update Information

INTRODUCTION

The software for the VT55 TPMS tool is updated periodically to add new vehicles, fix software bugs, and enhance the tool's function. You can use

the ATEQ update wizard to download software and firmware to your VT55 using a PC and the Internet. It is extremely important to use the latest

VT55 software to ensure that the current TPMS initialization and diagnostic procedures are used.

American Honda has a policy to ensure that VT55 tools are updated promptly. The VT55 software must be updated within 3 days of receiving

notification of an available update from an iN message or other Honda communication. If an out-of-date version is used, any TPMS replacements

will not be covered under warranty.

VT55 UPDATE REQUIREMENTS

^ VT55 Tool Kit (includes VT55, AC adapter, USB cable and CD): P/N AEQVT55

^ USB Cable (this cable came with the VT55): P/N AEQVT555

^ Internet access

^ A PC with Windows XP operating system or later (only 32-bit operating systems are supported)

To order the VT55, or the USB connector, go to the Acura Tool and Equipment catalog. Go to the iN > SERVICE > Service Bay> Tool and

Equipment Program, or call 888-424-6857.

SOFTWARE VERSION

To determine the latest software version, go to the iN > SERVICE > Service Bay> Diagnostic Tools Software Versions.

To check the VT55 version software, turn on the unit and the version number appears for about 2 seconds during the startup process. If you miss it,

turn the VT55 off by pressing and holding the power switch for about 2 seconds, then turn it back on.

WARRANTY CLAIM INFORMATION

None. This service bulletin is for information purposes only.

INSTALLING THE VT55 UPDATE SOFTWARE ON YOUR COMPUTER

NOTE:

The screens shown in this procedure may differ slightly due to PC variations.

1. Go online to update.ateq.com/software/webvt/update_webvt.zip

135

2. Enter the login and password.

Login: webvt

Password: update

3. The File Download screen appears. Select Save. The Zip file will be saved to your computer.

4. After the Zip file finishes downloading, open the update_webvt.zip file by double-clicking on it.

5. The WinZip - update_webvt.zip screen appears. Double-click on the .exe file.

NOTE:

If you see a Compressed (Zipped) Folders Error, contact your IT person because there is a permissions issue with your firewall.

6. The WinZip Caution screen appears. Select Yes.

136

7. The InstallShield Wizard screen appears. Select Next.

8. The InstallShield Wizard asks you to select a destination for the VT55 files. Select Next.

9. The InstallShield Wizard asks it you want to automatically start the WebVT application when you start your computer. Select Yes.

10. The InstallShield Wizard will prompt you when WebVT is installed on your computer. Select Finish.

137

11. The serial emulation port driver installer screen appears. Connect your VT55, and turn it on. Select Next.

12. After a few seconds, the serial emulation port driver installer prompts you when it is finished. Select Finish.

13. If you have any problems installing the VT55 update software, call ATEQ at 734-838-3100, and select option 3 for service.

14. Once the VT55 is updated to the current software version, go to VT55 UPDATE INSTRUCTIONS.

VT55 UPDATE INSTRUCTIONS

NOTE:

^ Some screens may list the tool as VT50 or VT55. This is OK; it will not affect updating the tool.

^ If at any time during the update an error message appears, or the VT55 is not detected, see the Standard User Guide that is on the ATEQ CD

that came with the tool, or call ATEQ at 734-838-3100, and select option 3 for service.

1. Go to your desktop, and double-click the WebVT icon to launch the VT55 update software.

2. Connect the VT55 to your PC with the USB cable, then turn it on. The serial number and current software version automatically display.

138

3. The Found New Hardware Wizard may appear. If it does, select Yes, now and every time I connect a device, then select Next.

4. The Found New Hardware Wizard prompts you to install the ATEQ RS232 Emulation software. Select Install the software automatically

(Recommended), then select Next.

5. The Found New Hardware Wizard will prompt you when the software is installed. Select Finish.

6. Select UPDATE DEVICE. Depending on your Internet connection, you may be prompted for a login and password. If you know your login and

password, enter them, otherwise, contact your administrator or internet service provider for the login and password.

7. If a new software version is available, you'll see a message asking if you want to update the VT55. Select Yes.

139

NOTE:

Do not disconnect the VT55 during the update procedure, as you may permanently damage the tool.

If no new software version is available, you'll see a message asking if you want to overwrite the existing software. Select No.

8. The Dealer Identification screen appears. Enter your 6-digit dealer number, then select Apply.

9. If the dealer number is valid, your dealership's name and address appears in the dealer information box. Select NEXT.

If the dealership number is not valid, call the American Honda Special Tools Hotline for assistance at 800-346-6327.

10. The VT55 begins updating. When the VT55 is finished updating, you'll see a message stating the update is done. Disconnect the VT55, then

select OK.

11. Let the VT55 turn off (for about 1 minute). Turn it on, and confirm that the software is updated to the software version you observed in

SOFTWARE VERSION on page 1.

12. If you have more than one VT55, repeat the update procedure for each unit.

13. Once all VT55s are updated, select EXIT, and store the USB cable in a safe location for future updates.

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 08-051 Date: 130221

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 08-051 Date: 130221

AcuraLink(R) - Warranty Exchange, Out of Warranty Repair

08-051

February 21, 2013

Applies To:

See VEHICLES AFFECTED

AcuraLink Control Unit (XM/HIP Receiver) In-Warranty Exchange/

Out-of-Warranty Repair

(Supersedes 08-051, dated March 7, 2011, to revise the information marked by the black bars and asterisks)

REVISION SUMMARY

*^ Under VEHICLES AFFECTED, the model years and models were changed.

^ Under PARTS INFORMATION, some 2012 and 2013 model year parts were added.*

BACKGROUND

Remanufactured AcuraLink control units

(XM receivers) are now available for certain models.

204

VEHICLES AFFECTED

205

PARTS INFORMATION

COMPONENT REPLACEMENT POLICY

Use only remanufactured components for warranty repairs on client vehicles. Follow the warranty information and procedures given in this service

bulletin.

^ Use new components to repair new, unsold vehicles.

^ A new component may be used to repair a client's vehicle only if the remanufactured component is currently unavailable from American Honda.

^ You must receive authorization from your District Parts and Service Manager (DPSM) before ordering a new component.

WARRANTY CLAIM INFORMATION

Operation Number: From the Flat Rate Manual

Flat Rate Time: From the Flat Rate Manual

Failed Part: Use the parts catalog in ISIS to look up the appropriate original factory equipped part number.

Defect Code: From the Flat Rate Manual

Symptom Code: From the Flat Rate Manual

Part used for repair: Use the RM part number from the repair order.

Example: P/N 39820-TL2-A52RM

Skill Level: Repair Technician

206

IN-WARRANTY EXCHANGE DIAGNOSIS

Service Consultant:

1. Interview the client to get as much information as possible. Information such as where and when the problem occurs is vital to the diagnosis

including any information/dates of exchanges between the client and XM support. This information also helps you to determine if the AcuraLink

control unit is operating normally, or if a problem exists with the client's XM account. Write the complaint on the repair order.

2. Call XM Satellite Radio at 800-852-9696 to verify the client's account status and the current services being provided. For example, is the client

paying for XM, but not traffic or weather?

NOTE:

Call and verify the account status.

Service Technician:

1. Print out the AcuraLink Control Unit Core Return Form from an iN workstation.

From the iN main menu:

- Click on SERVICE.

- Click on ISIS (Service Publications).

- Click on SEARCH BY VEHICLE.

- Enter the model and the model year.

- Enter keywords ACURALINK CORE RETURN.

- Select AcuraLink Control Unit Core Return

Form from the list.

2. Duplicate and confirm the problem using the client information written on the repair order, then write down the results on the repair order.

Using the SYMPTOM TROUBLESHOOTING INDEX in the appropriate service manual, find the symptom that matches the client's complaint,

and follow the diagnostic procedure:

^ Refer to the appropriate section in the service manual, or

^ From the iN main menu:

- Click on SERVICE.

- Click on ISIS (Service Publications).

- Click on SEARCH BY VEHICLE.

- Enter the model and the model year.

- Enter keyword ACURALINK.

- Select the appropriate Service Bulletin,

ServiceNews article, or Symptom

Troubleshooting from the list.

3. Repair the vehicle according to your diagnosis, then confirm the repair by trying to duplicate the client's original complaint:

^ If the problem is gone, return the vehicle to the client.

^ If the problem is still there, go to step 4.

4. Replace the AcuraLink control unit with a remanufactured unit:

^ For warranty repairs, go to IN-WARRANTY EXCHANGE.

^ For vehicle service contract (VSC) and certified used car (CUC) repairs, call.

For goodwill repairs, contact your DPSM.

207

IN-WARRANTY EXCHANGE

Service Technician:

1. If, after reviewing all publications available through the iN and talking directly to XM support you cannot repair the problem, order a

remanufactured AcuraLink control unit through the Open Ordering System.

2. You will receive a remanufactured AcuraLink control unit, packed in a reusable shipping box. Save this box and the packing materials. You must

return the failed AcuraLink control unit core in this box. Otherwise, your dealership risks being billed a $1,500.00 core loss charge and the core

will be sent back to your dealership.

3. Remove and replace the failed AcuraLink control unit:

^ Refer to the Audio, Navigation, and Telematics section of the appropriate service manual, or

^ From the iN main menu:

- Click on SERVICE.

- Click on ISIS (Service Publications).

- Click on SEARCH BY VEHICLE.

- Enter the model and the model year.

- Online, enter keywords ACURALINK REMOVAL, and select AcuraLink Control Unit (XM Receiver) Removal/Installation from the

list.

NOTE:

Call XM Satellite Radio at 800-852-9696 to update the client's account with the new XM/HIP serial number. Also, call Acura Client

Services to reactivate AcuraLink.

4. Make sure the failed AcuraLink control unit core is not disassembled. If the core is disassembled, your dealership will be debited a $1,500 core

loss charge.

5. Put the failed AcuraLink control unit core in the same box that the remanufactured unit came in.

Parts Manager:

6. Place the printed copy of the completed AcuraLink Control Unit Core Return Form and the paid warranty claim form into the core return box

with the failed AcuraLink control unit core.

7. Ship the failed AcuraLink control unit core to the appropriate location by using the prepaid shipping label that came with the remanufactured

AcuraLink control unit. If you need additional prepaid shipping labels, contact Remanufactured Parts Operations.

^ Complete the shipping label with your dealer information.

^ Pack one control unit per box, and use a separate shipping label for each one.

^ On the line requesting Your Internal Reference Information, enter YOUR DEALER NUMBER and the WARRANTY CLAIM NUMBER.

NOTE:

If the failed AcuraLink control unit core is not received at the specified address within 30 days from the warranty claim paid date, your

warranty claim will be debited, and your dealership will be issued a core loss fee of $1,500.

8. On the repair order, write down the warranty claim number, the original part number, the serial numbers from both the faulty and remanufactured

units, and the return tracking number.

9. Ship the faulty unit in the same box the remanufactured unit came in. Make sure you include this required paperwork:

^ A copy of the AcuraLink Control Unit Core Return Form.

^ A copy of the paid warranty claim.

NOTE:

If you return a failed AcuraLink control unit core without the proper forms, your warranty claim will be debited, and the core will be sent

back to your dealership.

OUT-OF-WARRANTY REPAIR

208

NOTE:

If you are making a repair or exchange because of a service bulletin or a service campaign, do not use OUT-OF-WARRANTY procedures. Refer

to IN-WARRANTY EXCHANGE for more information.

Service Consultant:

1. Give your client an estimate for repairing the unit (see step 6), plus the labor cost to replace it.

Service Technician:

2. Print out the Out-of-Warranty/New Replacement

AcuraLink Control Unit Repair Form.

^ From the iN main menu:

- Click on SERVICE.

- Click on ISIS (Service Publications).

- Click on SEARCH BY VEHICLE.

- Enter the model and the model year.

- Enter keywords ACURALINK REPAIR FORM.

- Select Out-of-Warranty/New Replacement

AcuraLink Control Unit Repair Form from

the list.

3. Fill out the technician section of the Out-of- Warranty/New Replacement AcuraLink Control Unit Repair Form.

4. Remove the faulty unit. Give the unit to your parts department.

Parts Manager:

5. Fill out the parts manager section of the Out-of-Warranty/New Replacement AcuraLink Control Unit Repair Form. Make sure you include your

name, a department, and a dealership phone number in the blank space on the repair form.

6. Contact the manufacturer to request an estimate for the cost of the repair plus shipping.

Prices are subject to change; please call for a current firm price on repair.

7. Get the required paperwork:

^ Paying by check - Issue a dealership check

made out to Pioneer Electronics for the cost of the repair and return shipping.

^ Paying by credit card (Visa or MasterCard only) - the control unit repair form must be completed by the parts manager. When you use a

credit card, fill in all of these fields:

- Credit card number

- Credit card expiration date

- Printed name (as shown on credit card)

- Signature (authorized card holder)

- Phone number

- Authorized charge amount

NOTE:

If you send a faulty unit without a check or complete credit card information, it may result in additional time to process your repair, and

the manufacturer may send the unit back to you unrepaired, or they may repair it and send it back C.O.D.

^ Make a copy of the completed Out-of-Warranty / New Replacement AcuraLink Control Unit Repair Form. If you send the manufacturer the

faulty unit without a copy of the form, they will hold the unit unrepaired until they receive one.

209

8. Carefully pack the faulty unit and the paperwork in a suitable box, and label the box clearly. You are responsible for lost or damaged units; keep

all shipping documents and insurance receipts.

9. Ship the faulty unit to Pioneer Electronics via UPS.

Pioneer Electronics Service, Inc.

2161 Dividend Dr.

Columbus, OH 43228

614-777-7200

NOTE:

^ The manufacturer will repair the unit and ship it back within 5-7 working days, via UPS Ground pre paid, or 2nd Day Air (whichever you

requested). Units damaged by misuse or mishandling cannot be shipped back within the usual 5-7 days.

^ The manufacturer guarantees the repair for 90 days from the date of the paid client repair order.

10. To check on the status of your repair order, call the manufacturer.

If your client has any further questions or concerns, have them call Acura Client Services.

NOTE:

A damaged unit may need extra repair. If so, the manufacturer will call you with an estimate of any added charges.

^ If you accept the estimate, mail a dealership check for the additional amount to the manufacturer, authorize the increased amount to be

applied to the credit card payment, or have the manufacturer ship the repaired unit back to you, and you pay the difference upon arrival

(C.O.D.).

^ If you reject the estimate, the faulty unit will be returned to you along with a refund. However, you will be charged $30.00 (C.O.D.) for

diagnosis, shipping, and handling. The unit will be shipped back to you, via UPS Ground.

Completing The Out-of-Warranty/New Replacement AcuraLink Control Unit Repair Form

210

211

212

NOTE:

It is very important that you fill out this form fully and accurately. An accurate explanation of the problem and conditions helps the manufacturer

to duplicate the problem, speeding the repair, and reducing the number of No Trouble Found" (NTF) units.

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 09-034 Date: 130327

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 09-034 Date: 130327

Electrical - GR8 Battery Diagnostic Station Update Information

09-034

March 27, 2013

Applies To:

ALL

GR8 Battery Diagnostic Station Update Information

(Supersedes 09-034, dated February 12, 2011; see REVISION SUMMARY)

REVISION SUMMARY

This service bulletin has been revised extensively. American Honda recommends that you review the entire bulletin.

INTRODUCTION

The software for the GR8 Battery Diagnostic Station is updated periodically to fix software bugs and enhance the tool's functionality. You can now

use the Midtronics GR8 update wizard to download software and firmware to your GR8 using a PC and the Internet. It is extremely important to use

the latest GR8 software to ensure that the current battery testing and diagnostic procedures are used.

Acura introduced a new policy to ensure that GR8 testers are updated promptly. The GR8 software must now be updated within 3 days of receiving

notification from an iN message or other Acura communication. If an out-of-date version is used, any battery or alternator replacements may not be

covered under warranty.

GR8 UPDATE REQUIREMENTS

^ GR8 Battery Diagnostic Station:

P/N MTRGR81100P

^ USB-to-mini-USB cable (supplied with the GR8):

Midtronics P/N A128

^ Internet access

^ An IBM-compatible PC with Windows 7, Vista or XP operating system and Internet Explorer 7 or 8

To order the GR8 Diagnostic Station or the USB-to-mini-USB cable, go to the Acura Tool and Equipment catalog on the iN (select Service >

Service Bay > Tool and Equipment > Online Catalog).

SOFTWARE INFORMATION

The current software version is listed online. Go to the iN (select Service > Service Bay > Diagnostic Tools Software Versions).

To check the GR8 software version, click on:

Language > Options > Info > Version

WARRANTY CLAIM INFORMATION

None. This service bulletin is for information only.

GR8 UPDATE INSTRUCTIONS

The update should take 10-15 minutes. Make sure that the update is not interrupted. If the update is interrupted, it could damage the GR8 and require

you to send the GR8 to Midtronics for repair. This repair is not covered by warranty.

NOTE:

The screens shown below are examples from a typical installation. Your screens may vary.

1. Make sure the GR8 is off and the SD card is removed.

142

2. Online, go to

http://www.midtronics.com/client-log-in

3. Enter the username and password listed below, then click Login.

Username: acuragr8

Password: acuragr8

4. You should see an image of the GR8 tester. Click on Update Software.

5. Fill in your dealer number, the service manager's name, and the GR8 serial number(s). The dealer name, the dealer address, and the dealer phone

number are automatically filled in. Click SUBMIT REQUEST.

6. You should see the image of the GR8 tester again. Click on the highlighted Acura GR8 Software Update link.

7. A File Download - Security Warning screen appears. Select Run.

8. A file will be downloaded to your computer. After it is finished, an Internet Explorer - Security Warning screen appears. Select Run.

143

9. The Midtronics Update Wizard appears. Refer to SOFTWARE INFORMATION to find the current software version.

10. Turn on the GR8, and follow the Update Wizard on-screen instructions.

11. When the update is complete, the Update Results screen appears, indicating the update was successful. Click Finish to close the Update Wizard.

12. Turn the GR8 off for 10 seconds. Reinstall the SD card, then turn the GR8 on, and confirm that the software is updated to the software version

listed under SOFTWARE VERSION.

13. If an error message appears anytime during the update, follow the on-screen instructions, and try updating the GR8 again. If the error message

does not go away, or if you have any other problems updating the GR8, call Midtronics.

14. If you have more than one GR8, repeat the update procedure for each unit.

15. Once all GR8s are updated, store the USB-to-mini-USB cable in a safe location for future updates.

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 07-027 Date: 120503

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # 07-027 Date: 120503

AcuraLink(R) - Control Unit Updating Information

07-027

May 3, 2012

Applies To:

ALL Vehicles With AcuraLink

Updating the AcuraLink Control Unit

(Supersedes 07-027, dated September 13, 2008, to revise the information marked by the black bars and asterisks)

REVISION SUMMARY

*^ In BACKGROUND, a note was added about GNA600 availability through the Acura Special Tool Loan Program.

^ In REQUIRED TOOLS AND EQUIPMENT, the Compact Flash (CF) Memory Card and Adapter, the 512 MB CF Card, and the PCMCIA to

CF Adapter were removed because they're no longer used in this update procedure.

^ In UPDATING THE ACURALINK CONTROL UNIT, the tools used in step 5 were revised.*

BACKGROUND

NOTE:

The procedures in this service bulletin are referenced in other service bulletins.

All Acura models equipped with the AcuraLink option have a reprogrammable AcuraLink control unit. This unit is also known as the XM (HIP)

receiver.

To update or reprogram the AcuraLink control unit, you need the vehicle and an Interactive Network (iN) workstation with the latest version of the

Honda Diagnostic System (HDS) software and the GNA600 unit.

30

NOTE:

^ For information on installing the HDS software to your iN workstation, refer to Installation Instructions for HDS PC Software in the Tool

Information menu under SEARCH BY PUBLICATION on ISIS.

^ Whenever you install a new AcuraLink control unit, you must use the AcuraLink control unit updating procedure to make sure it has the latest

software.

*^ The GNA600 is available from the Acura Special Tool Loan Program. To request the loan of a special tool, call.

^ To order replacement parts for the GNA600 Kit, log onto the Interactive Network (iN). Click on Service > Quick Links > Tool and Equipment

Program.*

This service bulletin describes these items:

^ Questions or problems with the AcuraLink update software, the GNA600 unit, or the Interactive Network

^ Required tools and equipment

^ Updating tips

^ Updating the AcuraLink control unit on 2007-08 TLs and 2007-09 MDXs

^ Updating the AcuraLink control unit on models other than 2007-08 TLs and 2007-09 MDXs

^ Verifying the AcuraLink system operation (described after each updating procedure)

WARRANTY CLAIM INFORMATION

Skill Level: Repair Technician

Refer to the specific service bulletin for the symptom

you are repairing.

QUESTIONS OR PROBLEMS WITH THE ACURALINK UPDATE SOFTWARE, THE GNA600

UNIT, OR THE INTERACTIVE NETWORK

For questions or problems with the AcuraLink update software or the GNA600, call the American Honda Special Tools Hotline.

For questions or problems with the Interactive Network (iN), call the iN Support Center.

31

REQUIRED TOOLS AND EQUIPMENT

iN Workstation (with the latest HDS software installed)

NOTE:

The GNA600 kit, the reprogramming cable, the cable adapter, and the memory card are available through the Acura Tool and Equipment

Program.

Go to the Interactive Network (iN), click on Service, then click on Service Bay, and select Tool and Equipment Program from the drop-down menu,

or call.

32

Updating the AcuraLink control unit requires these

items from the GNA600 kit:

UPDATING TIPS

^ Whenever you install a new AcuraLink control unit, you must use the AcuraLink control unit updating procedure to make sure it has the latest

software.

^ If you are updating a control unit in a new vehicle, make sure all the fuses are installed.

^ To prevent damage to the control unit, do not operate anything electrical (brakes, headlights, etc.) during the update.

^ If you encounter errors in the software or the updating process, follow the on-screen instructions or reboot the workstation, and try again.

^ There are five processes involved in updating the AcuraLink control unit:

33

^ Setting up the GNA600

^ Capturing the current program ID

^ Downloading the new software to the GNA600 unit

^ Updating the software in the AcuraLink control unit

^ Verifying the AcuraLink system operation

NOTE:

Before you update an AcuraLink control unit, read the entire procedure. The order of connecting and disconnecting connectors is critical, and

some steps must be done within a specified period of time. If the steps are not followed exactly as shown, you may have to repeat the procedure

from the beginning and, in some cases, you may damage the GNA600 unit and/or the AcuraLink control unit.

UPDATE THE ACURALINK CONTROL UNIT:

2007-08 TL AND 2007-09 MDX

1. Write down the XM audio presets.

2. Turn the ignition switch to LOCK (0).

3. Connect an Acura Diagnostic Battery Station (GR8-1100PA) to the battery, and select Power Supply from the Options menu. Follow the prompts

on the screen to start the power supply mode. If the battery station indicates that the battery must be charged before reprogramming, select YES

to charge the battery. Restart the power supply mode when the battery is fully charged.

Do not use a battery charger or the charging mode on the battery station when updating the AcuraLink control unit

[NOTICE]

If the battery dies during the updating procedure, the AcuraLink control unit will be permanently damaged.

At the workstation: Set up the GNA600 unit

4. If not already done, load the latest HDS software onto the iN workstation.

^ If the latest version is not loaded and you try to update a control unit, the software may indicate that the unit already has the latest software,

even though it does not.

^ For information on installing the HDS software to your iN workstation, refer to Installation Instructions for HDS PC Software in the Tool

Information menu under SEARCH BY PUBLICATION on ISIS.

*5. Make sure the 256 MB PCMCIA Memory Card is in the PCMCIA slot under the clear plastic cover on the GNA600 unit.*

6. From the Windows Start menu on your iN workstation, go to the Programs folder and select CM Update, and then select AcuraLink Update.

Follow the on-screen instructions. The on-screen instructions are summarized in the following steps.

7. Connect the USB PC interface cable to the workstation and to the GNA600.

8. Connect the GNA600 unit to the power supply unit, and connect the power supply unit to an electrical outlet. The GNA600 unit starts a

self-check, and after about 30 seconds, the LEDs on the GNA600 unit flash green and yellow. This indicates the GNA600 is ready to capture the

current program ID on the vehicle.

9. Disconnect the GNA600 unit from the USB PC interface cable and the power supply.

At the vehicle: Capture the current program ID

10. Make sure the ignition switch is turned to LOCK (0). Locate and disconnect the AcuraLink 5P connector.

NOTE:

The AcuraLink update software shows the connector location on the workstation screen.

11. Connect the black connector of the AcuraLink reprogramming cable adapter to the 5P connector (with female terminals) on the vehicle, then

connect the orange connector to the other 5P connector.

34

MDX shown for reference

12. Connect the blue No. 1 connector of the AcuraLink reprogramming cable to the blue connector of the reprogramming cable adapter.

13. Connect the black No. 2 connector of the AcuraLink reprogramming cable to the DLC cable. Connect the DLC cable to the GNA600 unit. The

LEDs on the GNA600 unit flash green and yellow. Within 30 seconds of the LEDs flashing, do step 14.

14. Connect the yellow No. 3 connector of the AcuraLink reprogramming cable to the yellow connector of the reprogramming cable adapter.

35

15. After the green LEDs on the GNA600 unit stay on, disconnect the DLC cable from the unit. The current program ID has been captured.

16. Disconnect the yellow No. 3 connector of the reprogramming cable from the cable adapter.

At the workstation: Download the new software to the GNA600 unit

17. Connect the USB PC interface cable to the GNA600 unit.

18. Connect the power supply cord to the GNA600 unit.

19. Follow the screen prompts on the iN workstation to download the latest software to the GNA600 unit. The on-screen messages indicate if the

AcuraLink control unit has the latest software programs.

^ If the AcuraLink control unit has the latest software programs, go to step 24.

^ If you see a screen that says, "Current Main Program ID Not Found" or "Current Sub-Program ID Not Found," select Enter to continue.

20. When the software download is completed, disconnect the USB PC interface cable and the power supply cord from the GNA600 unit.

At the vehicle: Update the software in the AcuraLink control unit

21. Reconnect the DLC cable to the GNA600.

22. Within 30 seconds of the LEDs on the GNA600 flashing green and yellow, reconnect the yellow No. 3 connector of the AcuraLink

reprogramming cable to the yellow connector of the reprogramming cable adapter.

NOTE:

The time to update the software in the AcuraLink control unit varies, depending on the size of the main and sub-update programs.

23. After the yellow LEDs on the GNA600 stay on and the reprogramming is complete, disconnect the DLC cable from the GNA600. The

AcuraLink

control unit has been updated.

24. Disconnect both cable adapter connectors from the vehicle, then wait at least 20 seconds before reconnecting the AcuraLink 5P connectors.

36

25. Reattach the 5P connector to its mounting location to prevent rattles.

26. Disconnect the reprogramming cable adapter from the reprogramming cable, and disconnect the reprogramming cable from the DLC cable

before

storing the GNA600 kit components.

Verify AcuraLink system operation

27. Do the AcuraLink self-diagnosis:

^ Turn the ignition switch to ON (II), and accept the navigation system disclaimer.

^ On the navigation buttons, press MAP/GUIDE, MENU, and CANCEL simultaneously until the "Select Diagnosis Items" screen comes on.

^ On the navigation screen, select XM (HIP).

^ Select XM (HIP) System Link.

^ Make sure the self-diagnosis is OK (all blocks are green). If a problem is indicated, refer to the appropriate service manual.

28. Enter the XM audio presets.

UPDATE THE ACURALINK CONTROL UNIT:

MODELS OTHER THAN 2007-08 TL AND 2007-09 MDX

1. Write down the XM audio presets.

2. Turn the ignition switch to LOCK (0).

3. Connect an Acura Diagnostic Battery Station (GR8-1100PA) to the battery, and select Power Supply from the Options menu. Follow the prompts

on the screen to start the power supply mode. If the battery station indicates that the battery must be charged before reprogramming, select YES

to charge the battery. Restart the power supply mode when the battery is fully charged.

Do not use a battery charger or the charging mode on the battery station when updating the AcuraLink control unit.

[NOTICE]

If the battery dies during the updating procedure, the AcuraLink control unit will be permanently damaged.

At the workstation: Set up the GNA600

4. If not already done, load the latest HDS software onto the iN workstation.

NOTE:

^ If the latest version is not loaded and you try to update a control unit, the software may indicate that the unit already has the latest

software, even though it does not.

^ For information on installing the HDS software to your iN workstation, refer to Installation Instructions for HDS PC Software in the Tool

Information menu under SEARCH BY PUBLICATION on ISIS.

*5. Make sure the 256 MB PCMCIA memory card is in the PCMCIA slot under the clear plastic cover on the GNA600 unit.*

6. From the Windows Start menu on your iN workstation, go to the Programs folder and select CM Update, and then select AcuraLink Update.

Follow the on-screen instructions. The on-screen instructions are summarized in the following steps.

7. Connect the GNA600 USB PC interface cable to the workstation and to the GNA600.

8. Connect the GNA600 unit to the power supply unit, and connect the power supply unit to an electrical outlet. The GNA600 starts a self-check,

37

and after about 30 seconds, the LEDs on the GNA600 flash green and yellow. This indicates the GNA600 is ready to capture the current program

ID on the vehicle.

9. Disconnect the GNA600 from the USB PC interface cable and the power supply.

At the vehicle: Capture the current program ID

10. Make sure the ignition switch is turned to LOCK (0), or the vehicle ignition is in the OFF mode. Locate and disconnect the AcuraLink 5P

connector. NOTE: The AcuraLink update software shows the

connector location on the workstation screen.

11. Connect the blue No. 1 connector of the AcuraLink reprogramming cable to the 5P connector (with male terminals) in the vehicle.

RDX shown for reference

12. Connect the black No. 2 connector of the AcuraLink reprogramming cable to the DLC cable. Connect the DLC cable to the GNA600. The

LEDs on the GNA600 flash green and yellow. Within 30 seconds of the LEDs flashing, do step 13.

13. Connect the yellow No. 3 connector of the Acuralink reprogramming cable to the other 5P connector.

14. After the green LEDs on the GNA600 stay on, disconnect the DLC cable from the GNA600. The current program ID has been captured.

15. Disconnect the yellow No. 3 connector of the reprogramming cable from the vehicle.

At the workstation: Download the new software to the GNA600

38

16. Connect the USB PC interface cable to the GNA600.

17. Connect the power supply cord to the GNA600.

18. Follow the screen prompts on the iN workstation to download the latest software to the GNA600 unit. The on-screen messages indicate if the

AcuraLink control unit has the latest software programs.

^ If the AcuraLink control unit has the latest

software programs, go to step 23.

^ If you see a screen that says, "Current Main [or

Sub] Program ID Not Found" or "Current Sub-Program ID Not Found," select Enter to continue.

19. Disconnect the USB PC interface cable and the

power supply cord from the GNA600.

At the vehicle: Update the software in the AcuraLink control unit

20. Reconnect the DLC cable to the GNA600.

21. Within 30 seconds of the LEDs on the GNA600 flashing green and yellow, reconnect the yellow No. 3 connector of the AcuraLink

reprogramming cable to the yellow connector of the reprogramming

cable adapter.

NOTE:

The time to update the software in the AcuraLink control unit varies, depending on the size of the main and sub-update programs.

22. After the yellow LEDs on the GNA600 stay on, disconnect the DLC cable from the GNA600. The AcuraLink control unit has been updated.

23. Disconnect both reprogramming cable connectors from the vehicle, then wait at least 20 seconds before reconnecting the AcuraLink 5P

connectors.

24. Reattach the 5P connector to its mounting location to prevent rattles.

25. Disconnect the reprogramming cable from the DLC cable before storing the GNA600 kit components.

39

Verify AcuraLink system operation

26. Do the AcuraLink self-diagnosis:

All models except 2009 RL, 2009 TL, and 2009 TSX

^ Turn the ignition switch to ON (II), and accept the navigation system disclaimer.

^ On the navigation buttons, press MAP/GUIDE, MENU, and CANCEL simultaneously until the "Select Diagnosis Items" screen comes on.

^ On the navigation screen, select XM (HIP).

^ Select XM (HIP) System Link.

^ Make sure the self-diagnosis is OK (all blocks

are green). If a problem is indicated, refer to the

appropriate service manual.

2009 RL, 2009 TL, and 2009 TSX

^ Turn the ignition switch to ON (II), or press the

engine start/stop button to select the ON mode,

and accept the navigation system disclaimer.

^ On the navigation buttons, press MAP/GUIDE, MENU, and CANCEL simultaneously until the "Select Diagnosis Items" screen comes on.

^ On the navigation screen, select Detail Information & Setting

^ Select XM (HIP) from the on-screen menu.

^ Select XM (HIP) System Link.

^ Make sure the self-diagnosis is OK (all blocks are green). If a problem is indicated, refer to the appropriate service manual.

27. Enter the XM audio presets.

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # NHTSA10V145000 Date: 100409

Disclaimer ***Acura ZDX V6-3.7L Technical Service Bulletin # NHTSA10V145000 Date: 100409

Recall 10V145000: Dashboard Replacement

VEHICLE MAKE/MODEL: MODEL YEAR(S):

Acura/ZDX 2010

MANUFACTURER: Honda (American Honda Motor Co.)

MFR'S REPORT DATE: April 09, 2010

NHTSA CAMPAIGN ID NUMBER: 10V145000

NHTSA ACTION NUMBER: N/A

110

COMPONENT: Air Bags

POTENTIAL NUMBER OF UNITS AFFECTED: 1854

SUMMARY:

Honda is recalling certain model year 2010 Acura ZDX passenger cars manufactured between November 12, 2009 and March 22, 2010. During the

manufacturing process, the dashboard covering material may have not been properly laser scored to allow complete deployment of the front

passenger's SRS airbag.

CONSEQUENCE:

In the event of a crash, the airbag will not deploy properly, increasing the risk of injury.

REMEDY:

Honda will notify owners and Acura dealers will inspect the dashboard covering material and replace it if necessary free of charge. The safety recall

is expected to begin on or about April 21, 2010. Owners may contact Acura Client Services at 1-800-382-2238.

NOTES:

Honda's recall campaign number is R34. Owners may also contact The National Highway Traffic Safety Administration's Vehicle Safety Hotline at